Why Understanding Essential Plumbing Skills is Crucial When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Crucial When Installing a Bathtub
Blog Article
Are you on the lookout for details around A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also often, tiling skills. Changing an old tub with a new one is also a reasonably tough project. If the old bathtub is readily available, the task can move easily; if you have to open up a wall surface to eliminate the old bathtub as well as place the new bathtub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly require an assistant to vacate the old tub and embeded in the new one. Ensure you have actually qualified yourself for the job and also are comfortable trying it. Instead of employing a service provider to take control of a halfway-completed project, it is better to think about utilizing one before you start. Chances are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your shower room if you have currently acquired a brand-new tub and do not need to change the setup of your previous water pipelines.
Your tools and material checklist should consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, turn on the taps to drain any kind of water staying in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the limited access that is usually the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin making certain that the washing machines are in place in between the faucet and also the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The former type must be attached to the faucet ends initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Making use of both wood boards under its feet, position the bathtub in the needed placement. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by checking the level and also changing the feet on the bathtub until the spirit level reviews degree.
To mount taps, fit the bottom of the outermost versatile tap port to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water as well as check all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the tub and likewise examine the overflow electrical outlet and also the normal outlet for leaks.
Ultimately, fix the bathroom paneling as explained in the producer's user's manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of a minimum of when as this will certainly resolve it into its last position.
Preparing for the Installation
To start with, the sustaining framework provided with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps device to avoid stress on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you use all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its last setting.
Tiling Around the Tub
In the location where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to split a rigid seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, leading to complications with dampness and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture fairly very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted person who reads on Tools You Need to Install a New Bathtub , I assumed sharing that topic was important. Do you know someone else who is inquisitive about the subject? Feel free to share it. We value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Plumbing woes? We help. Report this page